ATech Machine ZETA-02 A Guia de Instalação descarregar pdf (Página 24)

18 z ZETA6104 Installation Guide

RP240 Remote Operator Panel

GND

+5V

GND

SHLD

COM 1 COM 2

+5V

GND

SHLD

Rx+

RxÐ

Tx+

TxÐ

GND

If you will use RS-485 serial communication,

you must connect the RP240 to the

COM 1

connector (and connect the RP240's +5V lead

to the

+5V terminal on the I/O connector).

In addition, you will have to issue these

commands to configure the ZETA6104 to

communicate successfully with the RP240

connected to

COM 1 and with RS-485

connected to

COM 2.

PORT1........Select COM 1 as the affected port.

DRPCHK1.... On powerup, check for RP240 on COM 1.

PORT2........Select COM 2 as the affected port.

DRPCHK¯.... On powerup, do not check for RP240

..................on COM 2.

GND

SHLD

+5V

GND

SHLD

GND

ZÐ

Z+

BÐ

B+

AÐ

A+

+5V

GND

HOM

NEG

POS

TRG-A

TRG-B

OUT-A

GND

P-CUT

+5V

OUT-P

IN-P

AUX-P

V_I/O

COM 1 COM 2

ENCODER

LIMITS

I/O

Rx+

RxÐ

Tx+

TxÐ

GND

PROG

RP240 Connections when using RS-485

RP240 Back Plane

GND

+5V

Input Power

ZETA57-51(S) 1.26 11.9 25 60 97 145

ZETA57-51(P) 2.38 16.1 50 129 195 293

ZETA57-83(S) 1.51 12.7 27 80 120 180

ZETA57-83P 3.13 19.6 54 175 249 373

ZETA57-102(S) 1.76 13.6 30 80 124 185

ZETA57-102P 3.50 21.7 60 186 268 402

ZETA83-62(S) 2.26 15.5 50 120 186 278

ZETA83-62P 4.00 24.8 88 260 373 560

ZETA83-93(S) 2.88 18.4 52 180 250 376

ZETA83-93P 4.00 24.8 72 350 447 671

ZETA83-135(S) 3.50 21.7 57 193 272 408

ZETA83-135P 4.00 24.8 65 355 445 667

Compumotor

ZETA

AC POWER

Power Cable

Provided in ship kit (p/n 44-014768-01)

Length: 6.6 ft (2.0 m)

95-132 VAC

50/60 Hz

6104

INDEXER DRIVE

POWER

STEP

OVER TEMP

MOTOR FAULT

Power Input Specification

95-132VAC, 50/60Hz, single-phase

Peak Power requirements depend on the motor you use:

Motor Current Cabinet Peak Motor Peak Shaft Peak Total Volt-Amp

Type (Amps) Loss (W) Loss (W) Power (W) Power (W) Rating (VA)

OS2HB(S) 1.51 21.1 67 34 122 199

OS2HB(P) 3.01 39.1 187 79 305 466

OS21B(S) 1.88 22.6 61 67 150 240

OS21B(P) 3.75 48.8 180 114 343 509

OS22B(S) 2.14 20.4 55 89 165 262

OS22B(P) 4.00 44.5 147 165 357 542

RS31B(S) 2.26 20.0 50 120 200 300

RS31B(P) 4.00 40.0 110 240 400 600

RS32B(S) 2.88 30.4 61 149 241 372

RS32B(P) 4.00 48.8 170 226 445 668

RS33B(S) 3.50 33.3 73 210 316 493

RS33B(P) 4.00 56.6 164 299 519 769

(S): Series Configuration (P): Parallel Configuration

WARNING: The motor case (via the EARTH terminal) and the ZETA6104Õs SHLD

terminals are grounded through the AC power connector ground pin. You must provide

a proper AC power ground for safety purposes.

SHLD

EARTH

LEDs (after power is applied):

POWER .................. On (green).

STEP ....................... Off. Or green if motion is commanded.

OVER TEMP ........... Off. Or red if the internal sensor reaches 131°F (55°C).

MOTOR FAULT ...... Off. Or red if there is a short in the motor windings or motor cable,

or if the INTERLOCK jumper on the motor connector is removed or extended.

1 2 ... 19 20 21 22 23 24 25 26 27 28 29 ... 62 63

Comentários a estes Manuais

Sem comentários

ATech Machine ZETA-02 A Guia de Instalação Página 24

Comentários a estes Manuais

Manuais e produtos relacionados com Serras circulares ATech Machine ZETA-02 A